H12-261_V3.0-ENU

Practice H12-261_V3.0-ENU Exam

Is it difficult for you to decide to purchase Huawei H12-261_V3.0-ENU exam dumps questions? CertQueen provides FREE online HCIE-Routing & Switching (Written) V3.0 H12-261_V3.0-ENU exam questions below, and you can test your H12-261_V3.0-ENU skills first, and then decide whether to buy the full version or not. We promise you get the following advantages after purchasing our H12-261_V3.0-ENU exam dumps questions.
1.Free update in ONE year from the date of your purchase.
2.Full payment fee refund if you fail H12-261_V3.0-ENU exam with the dumps

Full H12-261_V3.0-ENU Exam Dump Here

Latest H12-261_V3.0-ENU Exam Dumps Questions

The dumps for H12-261_V3.0-ENU exam was last updated on Jun 25,2025 .

Viewing page 1 out of 25 pages.

Viewing questions 1 out of 128 questions

Question#1

Regarding the characteristics of CE dual-homing, which of the following statement is incorrect?

A. CE accesses the backbone network through two links. These two links can be used for load sharing or as active and standby links.

B. CE and PE form a CE dual-homing network, which can ensure high network availability.

C. The VRFs of two PEs connected to the same CE can belong to different VPNs.

D. In CE dual-homing networking, loops may occur, and route-tags can be used to solve loop problems.

Question#2

Mainstream Layer 2 technologies VXLAN, TRILL, NVGRE and MPLS, etc.

A. True

B. False

Question#3

IPv6 link-local addresses can be generated via stateless autoconfiguration

A. TRUE

B. FALSE

Question#4

Application of the two-speed double-barrel in traffic policing, the number of tokens in the C bucket is TC, a number of tokens in P bucket is TP. When a packet of length B enters, which of the following statements is correct? (Multiple choice)

A. If TP-B>0 and TC-B>0, the packet is marked as green.

B. If TP-B>0 and TC-B<0, the packet is marked as yellow.

C. If TP-B<0 and TC-B<0, the packet is marked as red.

D. If TP-B>0 and TC-B<0, the packet is marked as green.

Question#5

Two EBGP neighbors connected by two parallel cables. What method will you use to achieve
bidirectional load sharing between two EBGP neighbors connected through these two parallel serial
cables?

A. Configure the loopback interface to establish an EBGP neighbor relationship and configure EBGP Multi-hop. Configure the loopback interface as the update source, and then use IGP to implement equal-cost path load sharing between addresses.

B. Without any method, BGP automatically implements load sharing between different autonomous systems on the available links.

C. Use the command at both ends "ebgp-load-balance

D. Configure the EBGP neighbor relationship with the loopback interface as the update source. The IGP in each AS must have two equal-cost paths to the EBGP neighbor loopback address. You need to use the command "next-hop-local".

E. Configure the EBGP neighbor relationship with the loopback interface as the update source. The IGP in each AS needs to import two equal-cost paths to the EBGP neighbor loopback address. You need to use the commands ebgp-max-hop and next- Hop-local

Exam Code: H12-261_V3.0-ENU Q & A: 635 Q&As Updated: Jun 25,2025

Full H12-261_V3.0-ENU Exam Dumps Here

Exam Code: H12-261_V3.0-ENU
Q & A: 635 Q&As
Updated: Jun 25,2025

About H12-261_V3.0-ENU Dumps