SK0-005

Practice SK0-005 Exam

Is it difficult for you to decide to purchase CompTIA SK0-005 exam dumps questions? CertQueen provides FREE online CompTIA Server+ Certification Exam SK0-005 exam questions below, and you can test your SK0-005 skills first, and then decide whether to buy the full version or not. We promise you get the following advantages after purchasing our SK0-005 exam dumps questions.
1.Free update in ONE year from the date of your purchase.
2.Full payment fee refund if you fail SK0-005 exam with the dumps

Full SK0-005 Exam Dump Here

Latest SK0-005 Exam Dumps Questions

The dumps for SK0-005 exam was last updated on Jul 15,2025 .

Viewing page 1 out of 18 pages.

Viewing questions 1 out of 92 questions

Question#1

A server technician is placing a newly configured server into a corporate environment.
The server will be used by members of the accounting department, who are currently assigned by the VLAN identified below:

Which of the following IP address configurations should the technician assign to the new server so the members of the accounting group can access the server?

A. IP address: 172.16.25.90/24 Default gateway: 172.16.25.254

B. IP address: 172.16.25.101/16 Default gateway: 172.16.25.254

C. IP address: 172.16.25.254/24 Default gateway: 172.16.25.1

D. IP address: 172.16.26.101/24 Default gateway: 172.16.25.254

Explanation:
The IP address configuration that the technician should assign to the new server so the members of the accounting group can access the server is 172.16.25.90/24 for the IP address and 172.16.25.254 for the default gateway. This configuration matches the VLAN identified in the image, which has a network address of 172.16.25.0/24 and a subnet mask of 255.255.255.0. The IP address of the server must be within the same network range as the VLAN, which is from 172.16.25.1 to 172.16.25.254, excluding the network and broadcast addresses (172.16.25.0 and 172.16.25.255). The default gateway of the server must be the same as the VLAN, which is 172.16.25.254, to allow communication with other networks or devices outside the VLAN.
Reference: [CompTIA Server+ Certification Exam Objectives], Domain 4.0: Networking, Objective 4.1: Given a scenario, configure network settings for servers.

Question#2

A server technician is installing a Windows server OS on a physical server. The specifications for the installation call for a 4TB data volume.
To ensure the partition is available to the OS, the technician must verify the:

A. hardware is UEFI compliant

B. volume is formatted as GPT

C. volume is formatted as MBR

D. volume is spanned across multiple physical disk drives

Explanation:
To ensure the partition is available to the OS, the technician must verify that the volume is formatted as GPT. GPT (GUID Partition Table) is a partitioning scheme that defines how data is organized on a hard disk drive (HDD) or a solid state drive (SSD). GPT uses globally unique identifiers (GUIDs) to identify partitions and supports up to 128 primary partitions per disk. GPT also supports disks larger than 2 TB and has a backup copy of the partition table at the end of the disk for data recovery. GPT is required for installing Windows on UEFI-based PCs, which offer faster boot time and better security than legacy BIOS-based PCs.

Question#3

A technician has received tickets responding a server is responding slowly during business hours.
Which of the following should the technician implement so the team will be informed of this behavior in real time?

A. Log rotation

B. Alerts

C. Reports

D. Log stopping

Explanation:
Alerts are notifications that inform the technician or the team of any issues or events that occur on a server or a network. Alerts can be configured to trigger based on certain thresholds, such as CPU usage, disk space, memory utilization, or response time. Alerts can help the technician monitor and troubleshoot the server performance in real time.
Verified Reference: [Alerts], [Server performance]

Question#4

A server is reporting a hard drive S.M.A.R.T. error. When a technician checks on the drive, however, it appears that all drives in the server are functioning normally.
Which of the following is the reason for this issue?

A. A

B. error is a predictive failure notice. The drive will fail in the near future and should be replaced at the next earliest time possible

C. A

D. error is a write operation error. It has detected that the write sent to the drive was incorrectly formatted and has requested a retransmission of the write from the controller

E. A

F. error is simply a bad sector. The drive has marked the sector as bad and will continue to function properly

G. A

H. error is an ECC error. Due to error checking and correcting, the drive has corrected the missing bit and completed the write operation correctly.

Explanation:
A S.M.A.R.T. error is a predictive failure notice. The drive will fail in the near future and should be replaced at the next earliest time possible. S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a feature that monitors the health and performance of hard drives and alerts the user of any potential problems or failures. S.M.A.R.T. can detect various indicators of drive degradation, such as bad sectors, read/write errors, temperature, or spin-up time. If a S.M.A.R.T. error is reported, it means that the drive has exceeded a predefined threshold of acceptable operation and is likely to fail soon. The drive may still function normally for a while, but it is recommended to back up the data and replace the drive as soon as possible to avoid data loss or system downtime.

Question#5

Data availability is a high priority, even in the case of multiple hard drive failures.
Which of the following are the BEST options to comply with the user requirements? (Choose three.)

A. Install the OS on a RAID 0 array.

B. Install the OS on a RAID 1 array.

C. Configure RAID 1 for the application data.

D. Configure RAID 5 for the application data.

E. Use SSD hard drives for the data application array.

F. Use SATA hard drives for the data application array.

G. Use a single JBOD for OS and application data.

Explanation:
To comply with the user requirements, the best options are to install the OS on a RAID 1 array, configure RAID 5 for the application data, and use SSD hard drives for the data application array.
Here is why:
RAID 1 is a mirroring technique that creates an exact copy of data on two disks. This provides redundancy and fault tolerance in case of hard drive failure. RAID 1 also improves read performance since either disk can be read at the same time. Therefore, installing the OS on a RAID 1 array meets the first requirement of separating the OS from the application data and protecting it from hard drive failure.
RAID 5 is a striping technique with parity that distributes data and parity blocks across three or more disks. This provides improved performance and storage efficiency compared to RAID 1, as well as fault tolerance in case of a single disk failure. Therefore, configuring RAID 5 for the application data meets the second and third requirements of providing high IOPS performance and data availability.
SSD hard drives are solid-state drives that use flash memory to store data. They have no moving parts and offer faster read and write speeds, lower latency, and lower power consumption than traditional HDDs. Therefore, using SSD hard drives for the data application array meets the second requirement of providing high IOPS performance.
Reference:
https://phoenixnap.com/kb/raid-levels-and-types
https://en.wikipedia.org/wiki/Standard_RAID_levels

Exam Code: SK0-005 Q & A: 481 Q&As Updated: Jul 15,2025

Full SK0-005 Exam Dumps Here

Exam Code: SK0-005
Q & A: 481 Q&As
Updated: Jul 15,2025

About SK0-005 Dumps